Your Plumbing Crash Course: A Guide to Bathtub Installation
Your Plumbing Crash Course: A Guide to Bathtub Installation
Blog Article
They are making several good pointers related to Tools You Need to Install a New Bathtub overall in the content just below.
Setting up a bath tub isn't specifically rocket science, but it does call for strong plumbing, carpentry, as well as in some cases, tiling abilities. Changing an old bathtub with a brand-new one is likewise a reasonably difficult job. If the old tub is readily obtainable, the task can relocate rapidly; if you need to open a wall surface to get rid of the old bathtub and also position the new tub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to vacate the old bathtub and set in the new one. Ensure you have actually certified on your own for the work and are comfortable attempting it. Rather than hiring a specialist to take over a halfway-completed project, it is better to consider employing one prior to you start. Possibilities are you may require a specialist plumber to make tube links.
This short article will aid you set up a new bath tub in your shower room if you have actually currently acquired a brand-new bathtub and also don't require to alter the plan of your previous water system pipelines.
Your devices and material checklist must consist of the following:
Getting ready for the Installment
To start with, the supporting framework provided with the bathroom needs to be fitted (if called for) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to see to it that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the taps device to stop pressure on the tub.
Fit the flexible faucet connectors to the bottom of the two faucets making use of 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you use all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath should currently be ready to be fitted in its final setting.
Removing Old Touches
If you need to change old taps with new ones as a part of your installment, then the first thing you must do is detach the water system. After doing so, activate the faucets to drain pipes any water continuing to be in the system. The process of getting rid of the existing faucets can be rather problematic as a result of the restricted gain access to that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the faucets. Have a cloth all set for the remaining water that will come from the pipelines. When the supply pipelines have been eliminated, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the single taps from turning during this procedure. As soon as the taps have been removed, the holes in the bath/basin will need to be cleaned of any old securing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Setting up the Tub
Using both wood boards under its feet, put the tub in the required setting. The wooden boards are practical in equally spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four small points.
The following goal is to guarantee that the bath tub is leveled all round. This can be accomplished by checking the level and also readjusting the feet on the bath tub up until the spirit level checks out level.
To set up taps, fit all-time low of the outermost versatile faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Switch on the water supply and also inspect all joints as well as new pipework for leakages as well as tighten them if required. Fill the bathtub and additionally examine the overflow outlet and the normal electrical outlet for leaks.
Lastly, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the bathtub ought to wait until the bath tub has been made use of at least once as this will certainly resolve it into its last position.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic connector to avoid damages to the string. One end of the port fits on the plastic tail of the faucet and also the various other end supplies a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly require decreasing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the faucet in the mounting hole in the bath/basin ensuring that the washing machines are in place between the tap as well as the sink. Protect the tap in place with the supplier supplied backnut. Once the faucet is firmly in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The former kind should be connected to the faucet finishes initially, tightening up only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the installation can relocate enough to break a rigid seal, causing the water to permeate the wall in between the bathroom and also the tiling, resulting in issues with moisture and feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures and fittings. They are offered in tubes and also cartridges, and also can securing voids approximately a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with twists of drenched paper or soft rope. Keep in mind to constantly fill up the bathtub with water prior to securing, to allow for the activity experienced when the bathtub is in usage. The sealer can split relatively very early if you do not take into account this motion prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently available on the marketplace. It is recommended to fit the floor tiles using water-resistant or water-proof sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that article about A Step-by-Step Guide to Installing a Bathtub while surfing the web. Sharing is good. Helping people is fun. Thank-you for your time spent reading it.
Act fast, Call us! Report this page